Figure 12 Rear Loader, Parcel Only - Long Description 3.5.3 Carrier Access (Arrow Lock) Door (Front Loader Designs) The carrier access door shall have accommodations for mounting either Arrow lock shown in figure 13 in such a manner that the modified Arrow lock cylinder is flush with the front of the compartment door and the standard Arrow lock is slightly recessed. 3.12 Marking For front-loading designs, there must be two inscriptions centered on the carrier access door: "U.S. MAIL" in a minimum of .50 inch high letters and "APPROVED BY THE POSTMASTER GENERAL" in a minimum of .18 inch high letters. To subscribe to this RSS feed, copy and paste this URL into your RSS reader. All mounting hardware shall meet the corrosion resistance requirements of this document. The cover or door shall prevent the mail from falling out between the cover or door and shelves, and be strong enough to prevent theft of the contents of adjoining receptacles by manually forcing the rear door or cover from the front of the receptacle through a compartment. All front loading receptacles shall have fixed solid backs. Figure 3 Front Loader, Double Column Single Master Door - Long Description (Note: These tests shall not be performed on the same test door.). . Keyless lock options and key tracking can operate as standalone solutions that do not require broadband capability, which may not always be available in certain areas. We recommended Vice President, Delivery Operations: Create and maintain a nationwide arrow key inventory and ensure units reconcile their local inventory semiannually to ensure key accountability. In compliance with ADA regulations, the high forward and high side reach shall be a maximum of 48" above the finished floor. These units are designed to provide separate parcel delivery capability for wall-mounted centralized mail receptacles installed without integral parcel compartments. The spring shall be of sufficient strength to close the door from any opened position. Jones and others sought USPS arrow keys so that they could steal mail. Site design / logo 2023 Stack Exchange Inc; user contributions licensed under CC BY-SA. Start completing the fillable fields and carefully type in required information. USPS ENGINEERING, DELIVERY AND RETAIL SYSTEMS 4.11.8 Rear Door/Panel (Rear Loading Designs only) The rear cover shall be tested for a period not to exceed 3 minutes by attempting to force it to unseat. Receptacles submitted to the USPS (see 1.3) for final evaluation must be identical in every way to the receptacles to be marketed, and must be marked as specified in 3.11. Wholesale USPS & NCL Keys and Key Blanks | Ilco 1646R In the vertical direction, the customer lock and the numbers shall be the same centerline. 1.3 Approved Manufacturers A list of approved manufacturers is available upon request from: Why did DOS-based Windows require HIMEM.SYS to boot? In addition, no compartment size shall be offered as approved that is larger than any Postal Service tested and approved size for that particular manufacturer. What is the symbol (which looks similar to an equals sign) called? 6.1.3.4 Quality Policy Manual Manufacturer shall submit its quality policy manual to the address listed in section 1.3. Documents of external origin are identified and controlled. Contact: Craig Lambert. 6.1.3 Final Review Manufacturers shall submit two representative samples of the largest (typically, the highest total-compartment) version to the USPS for security testing, final review and approval. 5.3.4 Control of Nonconforming Product The control method and disposition process shall be defined and ensure that any product or material that does not conform to the approved design is identified and controlled to prevent its unintended use or delivery. I know that USPS policy has been shifting towards centralized delivery in recent years, so that they no longer have to visit individual addresses in order to deliver mail. What's up guys! The USPS will install Arrow locks, on request, free of charge. You can also download a key log template from the internet. No part of the receptacle may show finish corrosion, blistering, or peeling, or other destructive reaction upon conclusion of test. The lock-mounting hole in the door shall be able to withstand 100 foot-pounds of torque applied in the plane of the door, preventing the lock from being turned in the door allowing unauthorized entry into the compartment. A 3-pound hammer shall be used for a time period not to exceed 1 minute in tandem with these other tools during the tests of the seams and gaps around the perimeter of this item. In addition to outlining the approved sources approach to quality, the documentation should specify the methodology used to accomplish the interlinked processes and describe how they are controlled. In addition, no offered outgoing mail compartment height shall preclude any of the critical installation requirements, or any other requirement, from being met, and no compartment size shall be offered that is larger than any fully tested size. Forms. Semiannual reconciliation to a master inventory by units would provide enhanced accountability and security over these keys.

Snooze Eatery Nutrition Information, Shooting In Oxford, Nc 2021, Articles U