Memorize Holding Pattern Entries for Good King Schools 46.2K subscribers Subscribe 446K views 3 years ago Flying IFR Holding pattern entries are essential to safe IFR flight, and must be. To determine the type of entry, pilots can utilize many different methods: Raise the left side of the pencil 20 and see where the reciprocal course lies, Raise the right side of the pencil 20 and see where the reciprocal course lies, There will be cases in which the reciprocal will fall on, or very close to (5) a sector boundary in which case the entry procedures for either section are acceptable, When an aircraft is 3 minutes or less from a clearance limit and a clearance beyond the fix has not been received, the pilot is expected to start a speed reduction so that the aircraft will cross the fix, initially, at or below the maximum holding airspeed, Crossing the holding fix, perform the "5 Ts", Perform all turns at 3 per second; or 30 angle of bank; or 25 angle of bank if using a flight director system, whichever requires the least bank angle, After completion of outbound timing (according to altitude) or at the specified DME, turn (standard rate) to intercept the holding course inbound, During the last half of the turn, check the position of the head of the needle relative to the holding course, The head of the needle should always be in a place to fall onto the course when you're checking your turn inbound, If not on course, stop the turn with a double the angle intercept for VOR holding, When turning to intercept the inbound course in TACAN holding, an intercept greater than double the angle will be required, Begin timing once wings level inbound to the fix or station, This is to compensate for greater spacing between radials when holding away from the station, In TACAN holding, a 30 to 45 angle of intercept will establish the aircraft on the inbound course, Once established on course, commence tracking inbound to the holding fix, It is critical to establish the aircraft on course before crossing the holding fix, Continue to the station and initiate your turn in the direction of holding to begin the no wind orbit, Roll out of the turn on the outbound heading parallel to the holding course, Start the outbound leg timing, if required, when wings are level or abeam the station, whichever occurs later, If the abeam position cannot be determined, start timing when the turn to the outbound leg has been completed, When holding at a VOR station, pilots should begin the turn to the outbound leg at the time of the first complete reversal of the to/from indicator, At the completion of the outbound leg timing or at the specified DME, turn toward the holding radial to intercept the holding course, As you roll wings level, check the position of the head of the needle to the holding course, If they differ, note the number of degrees difference, This will determine the amount of heading correction to use on the outbound leg of your correction orbit, If you had to set an intercept when you turned inbound, there are winds to correct for, When checking the wind, resist the temptation to check wind from the head of the needle because it will be on the top of the RMI where you are looking; this will give you opposite winds causing an error, Establish the aircraft on the holding course and track inbound to the holding fix, Start inbound time at wings-level on the inbound course or on a heading to intercept the inbound course, whichever occurs first. (See FIG 5-3-8). Aircraft may be required to hold for a variety of reasons, including: Waiting for an Expect Further Clearance time, There are three types of holding, all of which instrument approach chart legends depict: [, Depicted as a solid bold line on an instrument approach [, In practice, holding in lieu is not really a holding pattern, but a method by which to turn around (course reversal), When used, you do not need to go outbound for the full distance but rather after 1 minute you should turn back in and execute the approach, Arrival patterns are used to control the flow of traffic on an approach, Depicted as a thin solid line on instrument charts, Think of it as adding a delay to ensure the airport environment is clear, The arrival holding pattern is not authorized unless assigned by ATC, Visually depicts holding following the execution of a, Depicted as a dashed line on instrument approach procedure, This pattern is considered the "published missed", Many times ATC will assign alternate instructions to facilitate traffic flow, especially during practice approaches, Holding areas must be designated as protected, i.e., free from obstacles, Holding pattern airspace protection is therefore provided by controlling the pattern's location and size, The FAA's standard pattern consists of right turns (think that most are right-handed, making that standard), Although non-standard, left turns may be assigned, Holding patterns depicted in the instrument approach plate legend show both left and right turns and are in no way an indication of standards, Logically, obstacle protection increases with altitude, More importantly, altitude impacts airspeeds due to the operation (aircraft operating at higher altitudes fly faster).

Mountain Brook City Council Members, Anthony Russo Fort Lauderdale, Biloxi To New Orleans Airport, Articles H